Go Back  DVD Talk Forum > DVD Discussions > DVD & Home Theater Gear
Reload this Page >

New Hardwood and Hiding Cables

DVD & Home Theater Gear Discuss DVD and Home Theater Equipment.

New Hardwood and Hiding Cables

Old 04-01-02, 06:04 PM
  #1  
BDB
DVD Talk Legend
Thread Starter
 
Join Date: Jan 2001
Location: Palm Springs and Los Angeles
Posts: 23,155
Received 106 Likes on 95 Posts
New Hardwood and Hiding Cables

I am getting hardwood floors installed in 2 weeks, they will be installed over plywood flooring. I have yet to speak to the installers about this but I was thinking of creating some sort of Canal in the plywood leading from Where my Receiver is at one wall to the opposite wall where my rears will be.

Has anyone done anything similar?

positives/negatives of having cable buried like that.
Old 04-01-02, 06:22 PM
  #2  
DVD Talk Ultimate Edition
 
Join Date: Jan 2001
Location: Seattle
Posts: 4,454
Likes: 0
Received 0 Likes on 0 Posts
You could use a router and make a nice channel in the subfloor. If they are putting in new subfloor you could obviously cut the plywood to make a channel.
Old 04-01-02, 07:08 PM
  #3  
BDB
DVD Talk Legend
Thread Starter
 
Join Date: Jan 2001
Location: Palm Springs and Los Angeles
Posts: 23,155
Received 106 Likes on 95 Posts
The subfloor is the concrete am I correct?
If so what is a router?
Old 04-01-02, 07:23 PM
  #4  
DVD Talk Ultimate Edition
 
Join Date: Jan 2001
Location: Seattle
Posts: 4,454
Likes: 0
Received 0 Likes on 0 Posts
Originally posted by BadlyDrawnBoy
The subfloor is the concrete am I correct?
If so what is a router?
Your foundation would most likely be concrete and then the subfloor would be plywood on top of that unless you have a basement(although your subfloor would still be plywood).

If there is existing plywood subfloor then you could use a router to route a channel in the wood. A router is a tool that is usually used to create a decorative or rounded over edge, like the edge of a table. A router can also be used to cut a channel in wood using the proper bit. You would plunge the channel cutting bit into the wood and drag it along to make your channel. Click here to see what a router looks like These can be rented cheaply from Home Depot or something or maybe you could talk the guys into installing the floor to do it for you.

If they are putting down a new subfloor of plywood they can cut the plywood to leave a small gap for you to run your wires.

One word of advice...if you do this run 2 pairs of everything...you never know what might happen to a set of wires and it's good to have a backup.
Old 04-02-02, 05:52 AM
  #5  
Sn0
DVD Talk Special Edition
 
Join Date: Dec 2000
Location: Too close to Kentucky
Posts: 1,420
Likes: 0
Received 0 Likes on 0 Posts
If he can channel through the plywood I would make sure the channel is deep enough that if you need to put a snake through there that it will fit, just my 2 cents.
Old 04-02-02, 01:28 PM
  #6  
New Member
 
Join Date: Jan 2002
Location: Vacaville, California
Posts: 12
Likes: 0
Received 0 Likes on 0 Posts
Stumbled across this stuff...

While link surfing I came across this.
Good idea! Might cost $$ depending on the application. But a good alternative.

http://www.decorp.com/

Steve

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.